TASCAM DM24 setup help!

  • Thread starter Thread starter rbsb*
  • Start date Start date
R

rbsb*

New member
can anyone tell me how to successfully route a given chanel to the FX on a tascam dm24.

I'm frustrated to no end, because either 1 effect works, or I create an internal loop somehow & get serious feedback.



I'm trying to do this:



Send audio from channel 17 & 18 to Aux5 for delay and aux 6 for reverb, and back to the main mix without routing the FX outputs to channel's 21 thru 32.






HELP me before I break something! Haha!

You guys always come thru for me in my moments of need!!



*RB
 
rbsb* said:
can anyone tell me how to successfully route a given chanel to the FX on a tascam dm24.

I'm frustrated to no end, because either 1 effect works, or I create an internal loop somehow & get serious feedback.



I'm trying to do this:



Send audio from channel 17 & 18 to Aux5 for delay and aux 6 for reverb, and back to the main mix without routing the FX outputs to channel's 21 thru 32.






HELP me before I break something! Haha!

You guys always come thru for me in my moments of need!!



*RB
Click to expand...

PM me. This unit is so routable thats there is no one way of doing it.
 
FX Setup

Malcom123,
I just got this from tascam today. I haven't tried it yet, because I haven't made it home, but it should work.

See below and good luck :rolleyes: :

Below are the instructions you requested.


Using CH1
With music playing though speakers


With in the MONITOR section
Press the STEREO button


Assigning the output of the effect module to a channel:
Press "SHIFT" until the light turns on
Press "I/O"
Press "CH17-32 IN"
For CH25 select "EFF 1-L" Press enter (you can use any CH as your return)
For CH26 select "EFF 1-R" Press enter (you can use any CH as your return)
Move the "Patch cord" until CH25 and "EFF1-L" are connected
Move the "Patch cord" until CH26 and "EFF1-R" are connected

Assigning the input to the effect module:
Press the "EFFECT" button
Press "PATCH"
Select "LOOP / INSERT"
Select AUX 3 next to IN L (you can use any AUX )
CH25 should be next to OUT L
CH26 should be next to OUT R (IF CH26 is not next to OUT R, select "Stereo" and than select "Mono")


Individual effect send:
Press the "CH 1 - 16" button under Layer Status (light should be solid)
Press "SHIFT" until the light is off
Press "AUX 3 / 4 "
"CH 1 - 16" button under Layer Status (light should be blinking)
Move fader 1 up (this will send audio to the effect module)
Any fader pull up will send to the effect module


Master Effect send
Press the "MODULE" button
Press the "MASTER" button under Layer Status (light should be solid)
Move faders "AUX3" and "AUX4" up to 0


Effect return:
Press the "CH 17 - 32" button under Layer Status (light should be solid)
Move faders 25 and 26 to desired return level










Tascam Operation Support
 
I tried this last night and it worked purrrrrrfectly!!! Hope it works for you.
 
bchilders said:
I tried this last night and it worked purrrrrrfectly!!! Hope it works for you.
Click to expand...


Yeah, Mine works fine although I had a few setbacks with it. Mainly because I was muting channels 25&26 ( I think ) while testing.

I use stereo, Aux 1-2 for effects 1 and 3-4 for for effects 2

Very Flexible Console.

Still kinda learning it !

Malcolm
 
You must log in or register to reply here.
Back
Top