Search results

Hi, Will you setup a consumer's 2.1 speaker as B Monitor for check the mix?

Wow... Now I learned something! Haha. So, I shall replace the battery! In fact, what do you think about "Signal Buffer" thingy? Is that happens on those smaller or cheap multi effects pedal?

Oh my God, that simple? Is this means new battery replaced then everything will be alright? And the High Tone will be back then? No more "Signal Buffer" issue?

My setup was simple for small scale performance : * Vocal & Guitar * Traditional 8 XLR inputs Mixer (Yamaha) without built in amp * L & R Master Signal Output to 12 inch Powered Loud Speaker (without limiter / compression / any processors) * Vocal/Mic input, clean and direct to the XLR channel...

Appreciate again! I was hooked up my old Zoom G2.1u to applies the Chorus - Delay - Reverbs (without compression), as well we EQ and Patching for Rhythm, Plucking and Solo (with different output volume) So, when Solo or Plucking was playing, there was no such Lost High Tone or High Frequency...

Hi, It was in Live and I'm sorry that have no devices for recording. Btw, some say it's all about "Signal Buffer / True Bypass" ?

Hi, Recently, I'm facing a weird issue. When I was singing with my Acoustic Guitar (with Multi Effects Pedal) , high frequency was compressed! When playing guitar alone, sounds great! I've double check only every single paths, there were no even a compressor or limiter applied! What's...

Hi, * Mastering in Mono mode is the best way far than Stereo? * Mastering with Mid-Side is necessary? To get better stereo result, outstanding Vocal?

Jonesey, That's what I heard about! Is this means, do all MIX in MONO before PAN and Effects?

Room Size: 12 ft x 8 ft x 8 ft (height) Acoustic Treatment: Front Bass Trap (Panel), Walls, Ceiling on Mixing Spot Monitor: Placed accordingly (the rules), Calibrated How does it mean? Appreciate, dudes!

So, you prefer Condenser Mic or Dynamic Mic for Podcast? Why?

Hi, I'm facing Harsh Mid Frequency issue during mixing in my studio. How would you recommend to solve or treat the issue? Should I name the specific requency range? ** will this caused the "Short of Low Frequency" during the mix?

Hi, * Should I Mix in MONO at first? * Stereo Effects Plugins should apply during Mono Mix (if Mono Mix should be the first stage) or during Stereo Mode?

Hi, Attached mp3 was showing the NOISE that I was/am facing during recording section. What was that issue and where was it come from, still, how to solve it? Recording setup: MacBook Pro USB Audio Interface Mic XLR input Power supplies from the same source

Indeed, when I used it for (from) Mac output with Max volume on both, sound quality still acceptable! But when sound from Mixer's (as audio interface via USB) headphone output (50-70%), sound started clipping on headphone (HA400 70%). Have no solution after googled for a few days.

Headphone impedance : 56ohm

Behringer UFX1204 (the mixer), headphone output 100ohm. Behringer HA400 (the headphone amp) , 12Volt 80ohm. ---------- Update ---------- Do you mean the Headphone Amp was something wrong?

Hi, Many thanks ! 1) If haven't tried yet, start with the headphones volume on the mixer at zero, HA-400 output Level at about 12 o'clock, and slowly increase the headphones control on the mixer. ** This resolved the issue, but it wasn't loud enough 2) I did try to output from "control room"...

Thanks for those tips! 1. Power adapter came with the Amp! 2. Headphone on Mixer's headphone output was perfectly good 3. Headphone Amp from Mac output, perfect! 4. Another headphone Amp, I'll check it out soon!

Thank you very much and you are so kind & friendly! Haaaa... 1. Yes, I was using the original power adapter came along with the box. 2. What and how should I check the Headphone amp by using the Digital Meter?