Search results

  1. ron-e-g

    M-600 Master Section Problem

    All d-sub on the back. Everything goes to Dsub/Bantam patchbays.
  2. ron-e-g

    M-600 Master Section Problem

    Notice the black wires.
  3. ron-e-g

    What's a MS16 really worth?

    I have a Tascam MS-16. I have seen several on ebay priced anywhere from $900 to $3000. But not selling! I have been offered one in (VERY) good condition for $1000. It would include the DBX units and meter panel with manual. Good Deal?
  4. ron-e-g

    M-600 Master Section Problem

    Hello, I've been occupied with calibrating my MS-16. So I put the console on the back burner. Now I'm ready to start troubleshooting a problem with the master section. Basically, I don't get audio out of the right channel through the tape returns or channel inputs. I bought a spare console for...
  5. ron-e-g

    MS16 Calabration

    This is 1kHz first REPRO then SYNC This is 10kHz REPRO then SYNC This is 100Hz REPRO then SYNC
  6. ron-e-g

    MS16 Calabration

    Back to this for now :mad:This is my display. Meter at 1k.
  7. ron-e-g

    MS16 Calabration

  8. ron-e-g

    MS16 Calabration

    Hey fgonza2, thats exactly what the seller said! OK so...dumb question # ( I lost count):facepalm: ! How do I read this RF generator dial? I can push any button on the Frequency selector and nothing changes in the volt meter, only the level knob will adj. the level of the meter. How do I know...
  9. ron-e-g

    MS16 Calabration

    Ok, Thanks. BTW I assume you mean this "1"?
  10. ron-e-g

    MS16 Calabration

    First..30 ips does cause the disappearing supply tape syndrome! :D OK, so to be sure before I start monkeying around with the azimuth on my machine.. BTW I don't disconnect the test equipment from the input I only leave it turned off. Is that a problem? This is how the scope is set-up; This...
  11. ron-e-g

    MS16 Calabration

    I've adj. the generator output as seen. in input mode in sync mode in repro mode Connections
  12. ron-e-g

    MS16 Calabration

    These are the settings/connections, and image on the scope.
  13. ron-e-g

    MS16 Calabration

    Jp, Wouldn't this do the same thing? Ron
  14. ron-e-g

    MS16 Calabration

    With both channels set the same I get this; This would seem to indicate an adjustment needed?
  15. ron-e-g

    MS16 Calabration

    I'm working through the first step in alignment and calibration...Azimuth. The following pictures show the trace I get and the settings used. I'm not so sure about the settings and the trace does not look anything like the MS16 manual. It does look very similar to the Tektronix illustration per...
  16. ron-e-g

    Potentiometer's for Tascam/Teac consoles

    sweetbeats, There are no other markings, other than the ALPS logo. The distance "between" the large tangs is approximately 9/16. the distance center to center the contacts and tangs is 1/4. I bought a second M600 console that has some damage to several input modules. I thought if it was...
  17. ron-e-g

    Potentiometer's for Tascam/Teac consoles

    Like these. All the ones I find have the heavy (Handel Bars) at the bottom. with the smaller (Pin) connections above.
  18. ron-e-g

    Potentiometer's for Tascam/Teac consoles

    Anyone know of a source for replacement pots, for the Alps used in the 80's boards? Mine..M-600. Thanks, Ron
  19. ron-e-g

    MS16 Calabration

    My arsenal so far. Also have a Tektronix 2213 on it's way!
  20. ron-e-g

    Connector ID

    Can anyone help me ID this connector? Hint..it connects the M-600 to power supply (common on other models). I just don't know what it's technical name is. And if it's only related to Tascam. Ron
Back
Top