Search results

Audacity can not use an ASIO driver and as far as I know it can not do multitrack. In Harrison Mixbus look at its setup to see if the input and output devices are available for the Tascam and set it so if it something else...

If the Lexar is a normal/standard CF card it should fit. Did the DP-02CF have a CF card in it when you got it or was it empty and you're trying to get one? Be aware that the mating pins inside the CF card slot can be bent and if the CF card doesn't go in and seat easily, do not try pushing...

This one should work fine........ https://www.bhphotovideo.com/c/product/1003355-REG/sandisk_sdcfxs_032g_a46_32gb_extreme_compact_flash.html Comparable to the recommended CF cards on Tascam's list that spantini posted. You could go larger, but importantly is the speed and UDMA numbers (ie: 120...

Disclaimer....I don't own an L20 nor have I played with one. The block diagram sort of suggests that the 'REC/PLAY' switch can disable the path of the input through to the L/R master buss. However the is a software switch called 'REC SOURCE' that depending where it's set sends the input to the...

Do you live where there is much humidity/dampness? Sometimes even where it is stored can be damp, but not obvious. A loss of signal from the mic might be moisture on the microphones capsule which can 'short out' the bias voltage on it and reduce the output and sometimes make noise. You could try...

When you speak, your voice will have a tendency to travel around a room and bounce off walls and other surfaces and may cause an 'echo' that the mic can pickup. It will have a short delay getting back to the mic and when recorded it adds an artifact of audio that isn't desirable. The goal of the...

Any noise in the recording sounding like wind or static? Possibly a damp capsule? Are you using a pop filter (which may reduce breathe moisture getting into the mic)?

While there has been suggestions of the RE20 or other dynamic and it would likely work OK, in my own opinion I would go for a decent LDC with it mind that you'll have room acoustics better in control sometime in the future. When I was looking for a better LDC than what I had, it was between a...

Since this the first day with the new Auray mic boom arm and putting it through its paces, thought I'd mount up the RE20 with a FetHead to see how it supported it :P. Gotta say I'm pleased with this boom arm so far. Keith, the boom arm offered in the B&H kit is the Auray model with an internal...

Boom arm..... this one was delivered to my doorstep this morning.... https://www.amazon.com/gp/product/B013TPXU3G/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 Got it set up and it's pretty stiff to move (which may be a good thing). Holds position even with a light weight mic. Includes a...

RE20 Demo's female.................. https://www.voices.com/profile/stilford/voice-over https://www.voices.com/profile/fkgrattan/voice-over

Miktek C7e? https://www.sweetwater.com/store/detail/C7e--miktek-c7e-large-diaphragm-condenser-microphone I don't do VO, but have a Miktek C1 which I consider one of my better vocal mics. Both the C1 and C7e have an internal switch that can give the mic two different voicings by changing the...

Take a look in this...... page 148 https://www.boss.info/us/support/by_product/br-800/owners_manuals/8fa93457-48ee-4054-b426-85a0b0cf7e35/

Proper name is 'conformal coating'............... https://www.techspray.com/the-essential-guide-to-conformal-coating When I worked in the military electronics industry many, many years ago it was a spray on application and likely much the same today. Some was epoxy based depending on the degree...

Does this get close to what you want? https://www.guitarcenter.com/Alto/Uber-FX.gc There is a version without FX also (cheaper and sometimes a Musicians Friend Deal of the Day)

I had a problem a few years back with the service drop to my house. What I was noticing was when I started my table saw the overhead incandescent lights were getting momentarily brighter. The lights were on the other half of the 120v supply leg from the breaker box than the saw. The transformer...

Maybe......(?) https://support.microsoft.com/en-us/windows/turn-on-app-permissions-for-your-microphone-in-windows-10-94991183-f69d-b4cf-4679-c98ca45f577a

The packaging is different, but should fit. Pigtail leads would need to be soldered to the pins of one gang of the pot to connect to the PCB (may need to orient the pin side of the pot away from the PCB and loop the pigtails back down to the board). Otherwise it has the 15mm shaft length, is...

The 'A' specifies a Log taper. The link below explains tapers a bit including the reverse log. https://www.potentiometers.com/potcomFAQ.cfm?FAQID=29 The '551F' is going to take some more digging.

Are there any numbers/letters on the pot (stamped or ink) which maybe a manufacturers part number which could be used to identify or cross reference what it is?