Search results

UPS wants around $200-250 to pack and ship-along with insurance.I don't know if I have the brackets that holds the meter bridge,but it would be pretty easy to fabricate something.I never used the MB,it's still in the box it came in. You can PM me if you are interested.$370 is fine-plus shipping.

Since caps.age,while it's apart you may as well swap out the power supply caps.

The propellant in the canned air was what flushed out the switches.They will get flaky again.Buy some replacement switches either through Tascam 2-3 bucks a piece or through Mouser or Digikey for less than a dollar apiece. All Tascam service was outsourced to a local repair place appox. 3...

PM sent.

It has to be disassembled from the bottom.The channel cards are mounted to the faceplate- you have to pull off the knobs and remove the nuts on the pot.shafts.The cards are connected together with the "Buss" cards.They have to be removed-carefully-to remove the channel cards.

PM sent

The Tascam AQ-65 autolocator will work with the 388.It has -among other things-a RTZ function.

Just look up tascam ma-ad8.It's the only one on there.

I have a number of Tascam open reel parts up for sale or trade for something interesting. 1 pc. MS-16 complete head block assy in new condition -$500 OBO 1 pc. 80-8 complete head block assy, in almost new condition $250 OBO 1 pair of Tascam 42 quarter inch half track heads new $150 OBO I also...

I have my MSR 16 set up for the ATR Magnetics stuff.Of course it needs to be re-biased for the tape-but you can slam the tape,bury the meters and drums kill.

Just buy it from the Teac parts dept.Parts@teac.com.Don't use the rubber conditioner on it.It melts the rubber. Terry is a great guy.I have used him for multiple PR and counter rollers.

A couple of things.When the 4069 fails it locks the unit into either the monitor mod or the stereo mode.Verify all the L-R routing in the channel strips are un assigned.Monitor section work? The monitor section will work only if all the L-R assign buttons are up.It's also real easy to break the...

That version 1.06 is really old.The only fix-at Tascam- was replacing the soldered in mask programmed processor. with version 2.00.Then it could be updated.Basically it means that unless you have the updated CPU you are pretty much out of luck.

Since the 488's don't have any kind of sync port,capstan motor speed drift will always be your enemy.Bouncing tracks to a extra machine has two problems,1. You are locked into the mix when you do the bounce,and 2.You are adding extra active circuitry both sending and receiving the mix-adding a...

I would be concerned about tape stretching or breaking depending upon the age of the tape.Then there is the edge damage to consider when FF and RWD multiple times.But if the customer is happy...

PRGRM BUSS inputs are post mixer.Think of the 388 as a 8 track-8x8- mixer feeding a 8 track recorder with the 8 PGRM BUSS inputs being summed with the 8 outputs of the mixer feeding the recorder.

Why make it sound like the record?Own it.

Tobacco and alcohol are "gateway" drugs too-along with Chocolate Chip Cookies.

Your statement"the take up reel is locked"means to me the take up reel will not move even when the unit is not powered up and you try to turn it manually.Is that true? There are infra red sensors connected to the tension arms to control the torque. They may have failed,have broken wires,there...

Did you solder both sides of the motherboard? Some of those feedthroughs have to be soldered from the cage side.Intermittent VU metering and sync/repo output are symptoms of that.You have to pull the R/P cards to get at them. If you look at the schematic you will see that the output leaves the...