Results 1 to 4 of 4

Thread: Solder Post-EQ Direct Outs on an Allen & Heath SR8

  1. #1
    Join Date
    Jan 2018
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    Solder Post-EQ Direct Outs on an Allen & Heath SR8

    Sign in to disable this ad
    So I picked up an SR8 really cheap a while back because the pres get rave reviews on forums. I figured I could use the main outs and aux sends to get 6 invidual outputs, but when I actually attempted this, I found that all the channels seem to bleed. Even panned 100% Left, a channel will still feed a tiny amount of signal to the Right output. Furthermore, sending a signal to one aux sends a small amount of the signal to every aux, which I find even more bizarre. Not a problem at all for live, or even for the studio if the full mix was being done entirely on the board, but I wanted to use the 8 beautiful pres and eqs to feed into my DAW individually so I could keep mixing. I found an old thread on the subject, which I can't link to because I'm a newbie and they don't let you until you've posted a few times. I find this irratating, seeing as how I went to reply to that thread, and the site asked me to start a new thread and link to the old one instead of bumping. Ah well. I'll try to post the link in the comments. The title was: Mod Allen & Heath for direct outs? The OP wanted to mod their SR16 for post EQ individual outs. Initially, people encouraged him, but the thread ends with two very negative replies, asserting that attempting this mod would likely wreck the board. I'm wondering if anyone has any experience with this type of thing and could help me out. Thanks!

    P.S.
    The last poster on the old thread tells the OP to just use the inserts as direct outs, which would work, except I love running things through guitar pedals with those inserts . Also the inserts are pre EQ, which would be a bummer, because the eq is not half bad.

  2. #2
    Join Date
    Aug 2005
    Location
    U.K.
    Age
    34
    Posts
    19,441
    Thanks
    1,202
    Thanked 1,021 Times in 902 Posts
    Rep Power
    1000000
    Hi Tedward,
    As far as I know the 'bump old threads' thing is a friendly warning but you should be able to proceed if you want.
    It's there because people often bump really old threads, without realising, having found them in searches etc.

    Anyway, I've promoted you to full user so you should be able to link etc now.

    Hopefully someone can tell you if that bleed is considered a fault or just a 'feature'.
    ---------- Steenaudio Website ----------

  3. #3
    Join Date
    Jan 2018
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Thanks, I'll bump the old thread and see if I get anything!

  4. #4
    Join Date
    Feb 2009
    Location
    northampton uk home of Dr Who and Blackstar Amps!
    Posts
    9,989
    Thanks
    1
    Thanked 667 Times in 631 Posts
    Rep Power
    9374894
    I cannot find schematics or even a decent signal block diagram for the mixer however, I would urge reading a copy of Duggy Self's Small Signal Audio amps" before embarking on any such project.

    Specifically (as I think someone alluded to in the other post) you need to be sure you don't load down the internal circuitry. At best you might screw gain and pan pot laws, at worst cause loss of headroom and distortion. Even instability.

    First task, talk to A&H and see if they can supply schematics.
    Next, identify the take off points in the mixer.

    Then build a 'buffer box' with 4 NE5532s with say, 100k input Zs and coupling cap of the right value (and polarity! Test for it!) An economical way to connect into the mixer would be to use the Tascam D-sub connection protocol.

    The outputs of the unity gain 5532s can be impedance balanced if you like or/and appropriate.

    You could power the B box from a 30Vish rat and use either a resistive splitter or GRMad and use an opamp to derive a 'centre rail'. I would not advise pulling any more juice from the old mixer's supply.

    Dave.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Mod Allen & Heath for direct outs?
    By wpaldridge in forum DIY, Mods, and Homebrew
    Replies: 10
    Last Post: 01-27-2018, 18:05
  2. Allen and Heath GL2200 Direct Outs
    By earlynovember73 in forum Mixing Techniques
    Replies: 3
    Last Post: 01-02-2011, 18:38
  3. Allen and Heath
    By Nitemare2970 in forum Digital Recording & Computers
    Replies: 4
    Last Post: 09-29-2009, 09:33
  4. Allen and Heath
    By bunglebungle in forum Mixing Techniques
    Replies: 6
    Last Post: 06-15-2004, 05:58
  5. allen & heath 16:2
    By seriousturtle in forum Mixing Techniques
    Replies: 0
    Last Post: 06-06-2001, 11:10

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •