Page 4 of 4 FirstFirst ... 2 3 4
Results 31 to 35 of 35

Thread: DIY MIDI CC Controller w/100mm sliders for under $100

  1. #31
    Join Date
    Oct 2019
    Posts
    1
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    Smile Awesome!

    Sign in to disable this ad
    hey bro, it's very useful, and i have a teensy 2.0 board,can it run your code to come ture the midi function?

  2. #32
    Join Date
    Oct 2020
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    hi Jbenson.

    it's fantastic what you did. is it possible to manage this with NRPNs and not cc controllers.
    I do not do electronics and it scares me a little ... do you think that no one can bring who can do that ...
    I do not even of my sight which decreases ... lo

    all the best

    eric
    Last edited by ericmusicstrasb; 10-18-2020 at 11:25.

  3. #33
    Join Date
    Jun 2006
    Location
    Austin, Texas
    Posts
    14,842
    Thanks
    89
    Thanked 683 Times in 624 Posts
    Rep Power
    21474865
    Quote Originally Posted by Chili View Post
    I've been looking to build a midi foot controller for DMX lighting for the band. The behringer FCB1010 is a good product to use but I really don't want to spend $150. Did you have to do any programming on the Teensy brd?
    Funny this thread popped back up, I recently finished my MIDI DMX light controller. I used the Teensy 3.2 board, a few switches and LED's. There was code already written for the board, but I learned some of it then customized it to fit my purposes.



    20201005_001032878_ios-jpg

    The second pic shows what my brain must look like at times. I didn't cut the wires to length nor wrapped them up into bundles, just let them go where ever. I mounted the Teensy board then built a bus board for all the grounds. The LEDs need a resistor and since only one or two LEDs are lit at any one time, I needed only one resistor. So, one side of the buss board is for LED ground, then the resistor connects them to the the other side where all the switches are grounded.

    20201005_001019218_ios-jpg

    When I was done, I put a zebrawood veneer on it. I should have veneered it before cutting all the holes, but I didn't think about it then. The two switches on the right are page switches so I can page through different groups of presets. There are three green LEDs for the pages and the switches cycle up or down through them. Then each preset switch has its own red LED. Eight preset switches and three pages gives me 24 presets.

    The unit sends Note On events through USB to my laptop which runs QLC+ DMX lighting control software. The software sends DMX control through a USB to DMX controller which go out to the lights.

    20201019_021154756_ios-jpg

    I've used this unit for a couple of gigs already and it worked quite well.

  4. #34
    Join Date
    Oct 2020
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    well done!!!
    I dream of knowing how to do that. I don't know anything about it and I wonder if we can put motorized faders.

    i want to do this.

    vue-3d-de-la-personaisation-de-deux-bcn44-panneau-avant-v1-03-jpgvue-3d-de-la-personaisation-de-deux-bcn44-panneau-avant-v1-04-jpg

    I am using two behringer bcn44 coupled together for this.

  5. #35
    Join Date
    Oct 2020
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    vue-3d-de-la-personaisation-de-deux-bcn44-panneau-avant-v1-04-jpg

    I have many questions.

    can we put motorized faders. if it is possible how to weld them? how to change the program so that it is NRPN and not CC midi? I don't know anything if someone can help me

    bcn44 interface-midi-vue-de-dessous-jpgbcn-44-jpgplue-l-ctronique-1-avec-le-metre-jpg

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Rockwool LoftRoll Insulation 100mm Roll for Bass Traps
    By MeltdownStudio in forum Studio Building & Acoustic Treatment
    Replies: 9
    Last Post: 07-01-2015, 12:24
  2. Assigning MIDI Controller Sliders/Knobs to VST instruments in Cubase LE 4
    By ryant324 in forum Steinberg / Cubase User Forum
    Replies: 3
    Last Post: 01-13-2014, 14:08
  3. Midi Keyboard Controller vs. Midi Controller?
    By Xcaliber in forum Keyboards and Sound Modules
    Replies: 1
    Last Post: 08-04-2013, 13:43
  4. NYC: FLIGHT CASE EDITION Fatar 88 Weighted Key Controller!
    By ebot9000 in forum Free Ads for Music/Recording Equipment
    Replies: 1
    Last Post: 01-28-2010, 11:45
  5. How do MIDI sliders work
    By jamie_drum in forum Cakewalk / Sonar Forum
    Replies: 1
    Last Post: 01-10-2004, 07:18

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •