Recent content by powpowmeow

sounds like it's really compressed. it sounds great. love the snap. anyone know the gear they used to get that snare sound? i don't even know who produced that track. that's probably a good start. figure out who produced it, and then figure out what kind of compressor(s) they were fond of...

"sound wise" the guitars are "fuzz"y, varying from barely to highly overdriven. not a lot of clean guitars. no acoustics yet, just dealing with electrics. Mixing is in stereo. Using ableton live. Lots of plugins in the library. All guitar takes were recorded in stereo, discretely, with the...

does this noise sound familiar to you? mic is at4050 about a foot & a half away from 12" speaker only notice the noise when i play that last note in the clip. i hear it on other notes too, but not all (as you can hear in the clip). and the noise gets louder when i play louder. first thought...

only have 2 inputs to work with have 2 sm57's and an audio technica at4050 right now, the close mic is pointed pretty much at the edge of the speaker, which is the best "primary" mic sound i have found so far (see below) snip with the close mic at that angle, whats the best way to place...

I have an AT4050 - but lost the shockmount Mine looks like this: http://www.newworldproaudio.com/assets/images/microphones/atm_at4050_front_m.jpg Not the newer version. AT replacement shockmounts are $75+, so has anyone had success with a more "generic" shockmount with these style of AT mics...

system info: ableton live v8 windows 7 professional x64 lynx L22 card issue only happens when i change ableton's resolution from 24bit/48khz to 24bit/96khz. at 96khz, i get a bunch of "digital noise" this is the type of noise i associate with a bad video driver. but, my video card is brand...

i have been using 24 bit / 96 khz for a while. was wondering if there is any advantage to using different sampling rates? what do you guys use? any reason to use 192khz instead of 96khz, for example? i realize there is more headroom etc thanks!

I have no qualms buying second hand, so it's really $100 purchase on ebay. RNC 1773 seems to have a good reputation...

for recording only- i have been using a stripped down windows 7 enterprise edition with pretty good success. i went through and stripped out all the services, internet stuff, extra graphics, etc. (i have another hard drive with a separate boot for everything but audio) i was wondering about...

need a reference amp to power a couple monitors, under 300 bux if possible dont have the monitors yet, but i wont be having a huge power need with them or anything thanks!

Maybe this belongs in Newbie forum, but rather than buy new cables, can I use an XLR to 1/4" adapter without a loss in signal quality?

just picked up a lynx L22, unforunately the only output on the analog breakout cable is 2x XLR in and 2x XLR out currently i am doing all my monitoring via headphones. in the near future i am planning on buying some monitors so i was thinking the smart thing to do would be to find a quality...

Thanks for the reply..this card is brand new to me, so i will try to follow along. I did a Restore Defaults, and still had the same issue. As far as relevant input-->output, there is not an input level shown on the mixer to begin with... Screenshot: on this screenshot i am inputting a signal...

Due to the fact that I am brand new to this piece of hardware, this could be something very simple I am overlooking. I opened up the Lynx Mixer and plugged an xlr into the In 1 analog input of the breakout cable. Recording fine, no problem, mixer software reading fine. (using sound forge 8 to...

got a spare room, a decent size, not too big not too small walls all 90 degree angles nothing odd about it i need to find the most cost-effective way to put up foam and whatnot on the walls to make it sound effective for mixing, monitoring, mastering would like to keep it as cheap as possible...